Yale SmartHome Alarm series Especificaciones descargar pdf (Pagina 11)

Control Panel Menu System in Detail

Entering Programming Mode

The programming mode is for you to conﬁgure

the system, and make any changes to the pre-set

functions.

If the system is in Disarmed (Alarm off) mode, follow

the steps below to enter the programming mode.

1 Press ‘menu’ key on the control panel.

The screen will prompt you to enter the PIN code.

P - M o d e e n t e r

P - C o d e . . . .

2 Key in your PIN code within 30 seconds.

Note

•PressP to clear the entered PIN. If the code ﬁeld

is empty, it will return to the Alarm Off screen.

3 Press 3 to continue.

The following message is displayed for 2 seconds.

P r o g r a m m e n u

M a k e a s e l e c t i o n

4 ThentheProgrammingMainMenuwilltypicallybe

displayed.

* S y s t e m t e s t

H o m e - a r m s e t

Note

•Thecursorisindicatedbyaashingdotontheleft

upper corner. It can be moved up and down by

pressing pq respectively.

5 The following items can be selected:

· Fault log (only if there is a fault condition)

· System Test

· Home-arm set.

· Devices

· Log

· Adv. Settings

· Tel. Settings

6 After making a selection by moving the cursor

to the desired item, press 3 to conﬁrm the

selection. The display will show you the individual

programming screen accordingly. Selecting P will

return to the Alarm Off screen.

Important Note

•Inprogrammingmode,ifnokeyispressedwithin

5 minutes, the panel will exit the programming

mode and return to the Alarm Off screen.

System Test

When System Test is selected, you will be given 4

different options: Sensor Test, External Siren (test),

Panel Siren (test) and Phone alert.

Sensor Test:

three beeps will sound during a screen self test. This

allows you to test the system without causing an

alarm. To test the control panel is receiving a signal,

do one of the following depending on the device:

1 Press button 8 and 9 together on the keypad

2 Press the test/learn button on the sensor

3 Press the help button

A chime will sound and the display will show you

which device is transmitting.The upper right corner

will show the radio signal strength ranging from 1 to

9 (strongest). Relocate the sensor if this is below 5

(unstable).

Ext. Siren and Panel Siren (test):

•Theexternalsirenandcontrolunit(panel)sirencan

be tested by pressing 3 when prompted. Press 3

once more to stop the siren.

Phone alert:

•Selectthisoptionforatestcallviaphonedialer.

Home-arm set.

The home mode allows the home to be partially

armed so that no one can get inside without ﬁrst

disarming the system. However, the person inside

the house can move freely around without triggering

the alarm. Home mode is usually used to protect the

ground ﬂoor when you are upstairs in bed.

To enable home arm, you will ﬁrst need to choose

the sensors to be ignored during this mode. It would

typically be the bedroom PIR etc if you want to arm

your system during the night.

Selecting this option, the screen will display:

Press test on

sensor to ignore

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 31 32

Comentarios a estos manuales

Sin comentarios

Yale SmartHome Alarm series Especificaciones Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Yale SmartHome Alarm series